15 hand tools

The 15 most useful hand tools

by Edward J. Thunderbird

No batteries, no cords, and they last a lifetime. These are the hand tools worth owning even if you have every power tool, and the ones that let you build a whole shed or house without electricity.

Buy good ones once. A quality hammer, square, level and tape will outlast you. Spend more on tools that measure and cut; spend less on pry bars and clamps.
Claw hammerDriving a 16d nail; hold near the end of the handleStart with light taps; then full swingsEye protection: nails and heads can fly#1

Claw hammer

Drives and pulls nails. Still the most-used tool in any toolbox.

$15 to $60

Tape measureMeasuring and marking a boardHook on the end moves on purpose (for inside and outside)Mark with a V: the point is the measurement#2

Tape measure

Every project starts with a measurement.

$10 to $35

Speed squareMarking a square line across a 2x4Lip on the edge = a true 90Also marks 45s and roof angles#3

Speed square

Draws square and angled lines, and lays out roof rafters.

$8 to $30

LevelChecking that a shelf is level before screwing it downBubble between the lines = levelEnd vials check plumb#4

Level

Checks level (flat) and plumb (straight up and down).

$10 to $150

Chalk lineSnapping a long straight cutting line on plywoodPull tight, lift straight up in the middle, let go: SNAPBlue chalk wipes off; red is permanent#5

Chalk line

Snaps long, perfectly straight lines in seconds.

$10 to $35

Utility knifeScoring drywall along a straightedgeCut away from your body and handChange blades often; dull ones slip#6

Utility knife

Cuts drywall, carpet, roofing, rope, boxes and plastic.

$8 to $25

Hand sawCross-cutting a 2x4 on a sawhorseMost Western saws cut on the pushStart with a few pull strokes#7

Hand saw

Cuts wood anywhere, with no power and no noise.

$15 to $60

Chisel and malletCutting a shallow notch (a hinge mortise) in a door edgeBevel side toward the wasteSharp chisels are safer than dull ones#8

Chisels and mallet

Cuts notches, cleans joints, and fits hinges and locks.

$25 to $150

Block planeShaving a sticking door edge or chamfering a boardSet it for paper-thin shavingsPlane with the grain, downhill#9

Block plane

Shaves wood: fixes sticking doors and smooths edges.

$30 to $200

ScrewdriversTightening a hinge screw by handMatch the tip to the screw head (Phillips #2 is most common)Push in hard while you turn so it does not cam out#10

Screwdrivers

Turns screws in places a drill cannot, and controls tiny ones.

$15 to $60

PliersLocking pliers gripping a rusted nut so it can be turnedLocking pliers clamp on and stay onSlip-joint, needle-nose: grip, bend wirePliers are not wrenches: they round off nuts#11

Pliers

Grip, hold, bend, cut and clamp.

$15 to $60

Wrenches and socketsTightening a bolt with a ratchet and socketPull toward you; do not pushSix-point sockets grip without rounding#12

Wrenches and sockets

Tightens and loosens nuts and bolts on everything from mowers to trucks.

$20 to $200

Pry bar (flat bar)Pulling an old nail and prying off trimSlip a scrap of wood under it to protect the surfaceA longer bar gives more leverage#13

Pry bar (flat bar)

Pulls nails, pries boards and moulding, and lifts heavy things.

$12 to $50

ClampsBar clamps holding a glued-up panel while it driesSnug, not crushing: a little glue should squeeze outAlternate clamps top and bottom to keep it flat#14

Clamps

A third and fourth hand: hold parts while you glue, cut or fasten.

$15 to $60 each

Brace and bitBoring a hole by hand, no electricity neededLean on the top knob, crank the handleBore from both sides to avoid splintering#15

Brace and bit

Bores clean holes by hand, with no power at all.

$20 to $80

At a glance

#ToolBest forTypical cost
1Claw hammerDrives and pulls nails. Still the most-used tool in any toolbox.$15 to $60
2Tape measureEvery project starts with a measurement.$10 to $35
3Speed squareDraws square and angled lines, and lays out roof rafters.$8 to $30
4LevelChecks level (flat) and plumb (straight up and down).$10 to $150
5Chalk lineSnaps long, perfectly straight lines in seconds.$10 to $35
6Utility knifeCuts drywall, carpet, roofing, rope, boxes and plastic.$8 to $25
7Hand sawCuts wood anywhere, with no power and no noise.$15 to $60
8Chisels and malletCuts notches, cleans joints, and fits hinges and locks.$25 to $150
9Block planeShaves wood: fixes sticking doors and smooths edges.$30 to $200
10ScrewdriversTurns screws in places a drill cannot, and controls tiny ones.$15 to $60
11PliersGrip, hold, bend, cut and clamp.$15 to $60
12Wrenches and socketsTightens and loosens nuts and bolts on everything from mowers to trucks.$20 to $200
13Pry bar (flat bar)Pulls nails, pries boards and moulding, and lifts heavy things.$12 to $50
14ClampsA third and fourth hand: hold parts while you glue, cut or fasten.$15 to $60 each
15Brace and bitBores clean holes by hand, with no power at all.$20 to $80

Prices are typical U.S. store prices checked November 17, 2026. They change often with sales; check the store. Tools Critical is not paid by any store or brand.