Project

Building a house: power tools vs. hand tools only

by Edward J. Thunderbird

Which tools build a house, step by step: with power tools, and with hand tools only, the way houses were built for centuries before electricity reached the job site.

Permits and pros. A house needs a building permit, plans that meet code, and inspections. Electrical, plumbing, gas and HVAC work usually must be done or signed off by licensed trades. This page covers the carpentry tools.
Step by stepIn picturesPower vs. handThe tool kits and cost
10Finished

Step by step: which tools do what

StepPower toolsHand tools onlyTip
Layout and foundationRotary hammer (SDS), Circular saw, Cordless drill/driver, Impact driver, plus Tape measure, Chalk line, LevelTape measure, Chalk line, Level, Speed square, Hand saw, Claw hammer, Brace and bitSquare the corners with the 3-4-5 rule (or 6-8-10). Concrete is usually formed and poured by a crew; the rotary hammer sets anchors in cured concrete.
Floor framingCircular saw, Miter saw, Framing nailer, Impact driverHand saw, Speed square, Claw hammer, Chalk line, LevelJoists every 16 inches; glue and nail or screw the subfloor.
Wall framingCircular saw, Miter saw, Framing nailer, Reciprocating sawHand saw, Claw hammer, Speed square, Chalk line, Level, Pry bar (flat bar)Walls are built flat on the floor, then tipped up, plumbed and braced.
Roof framingCircular saw, Framing nailer, Miter sawSpeed square, Hand saw, Claw hammer, Chalk line, Chisels and malletLay out one rafter with the speed or framing square, test it, then use it as a pattern.
Sheathing and roofingCircular saw, Framing nailer, Jigsaw (plus a roofing nailer)Hand saw, Claw hammer, Chalk line, Utility knifeSnap chalk lines to keep shingle rows straight.
Windows and doorsCordless drill/driver, Impact driver, Oscillating multi-toolLevel, Claw hammer, Screwdrivers, Block plane, Chisels and mallet, Utility knifeShim plumb and level before fastening.
SidingCircular saw, Miter saw, Framing nailerHand saw, Claw hammer, Chalk line, Utility knife, Level
DrywallCordless drill/driver, Oscillating multi-tool, Jigsaw (or a drywall screw gun)Utility knife, Claw hammer, Tape measure, ScrewdriversScore with a knife, snap, and cut the back paper.
Trim and cabinetsMiter saw, Table saw, Router, Random orbit sander, Cordless drill/driver (plus a brad nailer)Hand saw, Block plane, Chisels and mallet, Clamps, Claw hammer, LevelA miter box and back saw cut trim by hand; a coping saw fits inside corners.
Repairs and cleanupAngle grinder, Wet/dry shop vacuum, Reciprocating sawPry bar (flat bar), Pliers, Wrenches and sockets, Utility knife

The house going up, in pictures

Step 1: Layout and foundation

String lines show where the walls go1Layout and foundation

Power tools: Rotary hammer (SDS), Circular saw, Cordless drill/driver, Impact driver, plus Tape measure, Chalk line, Level

Hand tools only: Tape measure, Chalk line, Level, Speed square, Hand saw, Claw hammer, Brace and bit

Square the corners with the 3-4-5 rule (or 6-8-10). Concrete is usually formed and poured by a crew; the rotary hammer sets anchors in cured concrete.

Step 2: Floor framing

2Floor framing

Power tools: Circular saw, Miter saw, Framing nailer, Impact driver

Hand tools only: Hand saw, Speed square, Claw hammer, Chalk line, Level

Joists every 16 inches; glue and nail or screw the subfloor.

Step 3: Wall framing

Walls built flat, then raised3Wall framing

Power tools: Circular saw, Miter saw, Framing nailer, Reciprocating saw

Hand tools only: Hand saw, Claw hammer, Speed square, Chalk line, Level, Pry bar (flat bar)

Walls are built flat on the floor, then tipped up, plumbed and braced.

Step 4: Roof framing

Rafters, seen from the side, run up to the ridge board4Roof framing

Power tools: Circular saw, Framing nailer, Miter saw

Hand tools only: Speed square, Hand saw, Claw hammer, Chalk line, Chisels and mallet

Lay out one rafter with the speed or framing square, test it, then use it as a pattern.

Step 5: Sheathing and roofing

5Sheathing and roofing

Power tools: Circular saw, Framing nailer, Jigsaw (plus a roofing nailer)

Hand tools only: Hand saw, Claw hammer, Chalk line, Utility knife

Snap chalk lines to keep shingle rows straight.

Step 6: Windows and doors

6Windows and doors

Power tools: Cordless drill/driver, Impact driver, Oscillating multi-tool

Hand tools only: Level, Claw hammer, Screwdrivers, Block plane, Chisels and mallet, Utility knife

Shim plumb and level before fastening.

Step 7: Siding

7Siding and trim

Power tools: Circular saw, Miter saw, Framing nailer

Hand tools only: Hand saw, Claw hammer, Chalk line, Utility knife, Level

Step 8: Drywall

Screws every 12 to 16 inches into the studs8Drywall (inside)

Power tools: Cordless drill/driver, Oscillating multi-tool, Jigsaw (or a drywall screw gun)

Hand tools only: Utility knife, Claw hammer, Tape measure, Screwdrivers

Score with a knife, snap, and cut the back paper.

Step 9: Trim and cabinets

9Trim and cabinets (inside)

Power tools: Miter saw, Table saw, Router, Random orbit sander, Cordless drill/driver (plus a brad nailer)

Hand tools only: Hand saw, Block plane, Chisels and mallet, Clamps, Claw hammer, Level

A miter box and back saw cut trim by hand; a coping saw fits inside corners.

Done

10Finished

Power tools vs. hand tools only

Power toolsHand tools only
SpeedMuch faster: a framing nailer drives a nail in a fraction of a second; a circular saw cuts a 2x10 in secondsRough rule of thumb: carpentry takes two to four times as long
CrewA small crew can frame a house in a few weeksMore people, or more time
AccuracySaws and guides make repeat cuts easyExcellent in skilled hands; layout and sharp tools matter more
Power neededGenerator, temporary service, or batteriesNone
Tool costAbout $2,500 to $3,500 or moreAbout $500 to $1,000 for a full kit
Noise and dustLoud; dust collection neededQuiet
FatigueLessMore: framing hammers and hand saws are hard work all day
Best forAlmost every modern buildOff-grid sites, timber framing, small cabins, learning, and as backup when the power is out

Most builders use both: power tools for the heavy cutting and fastening, and hand tools for layout, fitting and finishing. Even a "power tools only" crew carries a tape, square, level, chalk line, knife and hammer.

The tool kits and what they cost

Power tool kit for a house

ToolGood-value pickPrice
Cordless drill/driverDeWalt 20V MAX drill and impact driver combo kitabout $150 to $200
Circular sawDeWalt 20V MAX brushless 7-1/4 inch circular saw (tool only)about $150 to $200
Reciprocating sawDeWalt 20V MAX XR reciprocating saw (tool only)about $150 to $200
JigsawBosch JS470E corded jigsawabout $130 to $160
Miter sawDeWalt 12 inch sliding compound miter saw (DWS779)about $350 to $400
Table sawDeWalt 8-1/4 inch compact jobsite table saw (DWE7485)about $400 to $450
Random orbit sanderBosch 5 inch random orbit sander (ROS20VSC)about $70 to $90
Angle grinderDeWalt 4-1/2 inch corded grinder (DWE402)about $90 to $120
Oscillating multi-toolDeWalt 20V MAX XR oscillating multi-tool (tool only)about $140 to $180
RouterMakita compact router (RT0701C)about $100 to $140
Rotary hammer (SDS)Bosch Bulldog Xtreme rotary hammer (11255VSR)about $200 to $240
Framing nailerMetabo HPT 21 degree pneumatic framing nailer (NR90AES1)about $200 to $260
Wet/dry shop vacuumRidgid 12 or 16 gallon NXT wet/dry vacabout $110 to $170
Totalabout $2,240 to $2,810

The drill pick is a drill and impact driver combo kit. Add a compressor (about $150 to $250) for a pneumatic nailer, extra batteries (about $100 to $200 each), a brad nailer for trim and a generator if there is no power on site.

Plus the hand tools every crew carries

ToolGood-value pickPrice
Tape measureStanley FatMax 25 ftabout $22 to $28
Speed squareSwanson 7 inch Speed Squareabout $10 to $15
LevelJohnson or Empire 48 inch box-beam levelabout $40 to $60
Chalk lineMilwaukee or Irwin speed-rewind chalk reelabout $15 to $25
Utility knifeMilwaukee Fastback folding knifeabout $15 to $20
Claw hammerEstwing 16 oz steel hammer with vinyl gripabout $30 to $40
Totalabout $132 to $188

Hand tools only: the full kit for a house

ToolGood-value pickPrice
Claw hammerEstwing 16 oz steel hammer with vinyl gripabout $30 to $40
Tape measureStanley FatMax 25 ftabout $22 to $28
Speed squareSwanson 7 inch Speed Squareabout $10 to $15
LevelJohnson or Empire 48 inch box-beam levelabout $40 to $60
Chalk lineMilwaukee or Irwin speed-rewind chalk reelabout $15 to $25
Utility knifeMilwaukee Fastback folding knifeabout $15 to $20
Hand sawStanley SharpTooth 20 inch sawabout $20 to $30
Chisels and malletIrwin Marples 4-piece chisel setabout $40 to $60
Block planeWoodRiver low-angle block planeabout $80 to $110
ScrewdriversCraftsman or Husky 10-piece screwdriver setabout $20 to $35
PliersIrwin Vise-Grip 10 inch curved-jaw locking pliersabout $15 to $25
Wrenches and socketsGearWrench ratcheting combination wrench setabout $60 to $100
Pry bar (flat bar)Estwing 15 inch pry barabout $20 to $30
ClampsPony pipe clamp fixtures plus 3/4 inch black pipeabout $15 to $25 each plus pipe
Brace and bitVintage brace plus an Irwin auger bit setabout $60 to $110
Totalabout $462 to $713

Clamps are priced each; plan on 4 to 6. Add a rip saw, a coping saw and miter box, a framing square, a plumb bob and string line, and a second hammer for a helper.

Prices are typical U.S. store prices checked November 17, 2026. They change often with sales; check the store. Tools Critical is not paid by any store or brand.