15 power tools

The 15 most useful power tools

by Edward J. Thunderbird

These 15 tools do almost all the cutting, drilling, fastening, shaping and cleanup for building, remodeling and ranch work. Each page explains why you would choose it, how to use it, how to maintain it, and where to buy it and what it costs.

Pick one battery brand. Cordless tools from one brand share batteries, and batteries are the expensive part. Buy a drill and impact driver combo kit first, then add bare tools (no battery) for less. See battery platforms.
Cordless drill/driverDrilling a pilot hole straight down into a boardLight pressure; let the bit workClutch low for screws,drill mode for holes#1

Cordless drill/driver

Drills holes and drives screws. If you buy one power tool, buy this one.

$60 to $250

Impact driverDriving a long screw into a 4x4 postHex bits only; it hammers as it turnsGreat for lag screws, deck screws, bolts#2

Impact driver

Drives long screws and lag bolts that would stall a drill.

$80 to $250

Circular sawCross-cutting a 2x10 on two sawhorsesBlade 1/4 inch below the boardSupport both sides so the cut does not pinch#3

Circular saw

The saw that builds houses: cuts boards and plywood fast and straight.

$60 to $400

Reciprocating sawCutting a tree limb, or a pipe or nails during demolitionPress the shoe against the workSwap blades: wood, metal or demolition#4

Reciprocating saw

The demolition saw: cuts nails, pipe, limbs and walls.

$60 to $260

JigsawCutting a curve in plywood clamped to a benchGood side DOWN: the blade cuts on the upstrokeSlow down on tight curves#5

Jigsaw

Cuts curves, circles and cut-outs in plywood and thin boards.

$40 to $230

Miter sawCutting trim and framing at exact anglesKeep your hand 6+ inches from the bladeLet the blade stop before lifting it#6

Miter saw

Perfect square and angled cross-cuts, every time.

$130 to $700

Table saw (seen from above)Ripping a long board with the fence and a push stickbladeFence keeps the board straightPush stick, guard and riving knife ONStand to the side of the blade, never directly behind it.#7

Table saw

The most accurate saw for ripping boards and plywood to width.

$300 to $2,000

Random orbit sanderSmoothing a tabletop, 80 to 120 to 220 gritLet its weight do it; do not press hardKeep it moving; hook up a vac#8

Random orbit sander

Smooths wood fast without leaving swirl marks.

$40 to $450

Angle grinderCutting steel angle iron with a cut-off wheelGuard on, side handle on, both handsFace shield and gloves; sparks fly far#9

Angle grinder

Cuts and grinds steel, sharpens tools, and cuts tile and stone.

$30 to $260

Oscillating multi-toolFlush-cutting a door jamb so new flooring slides underThe blade vibrates, not spinsCuts flush, plunges, scrapes and sands#10

Oscillating multi-tool

Flush cuts, plunge cuts, scraping and detail sanding in tight spots.

$60 to $400

RouterRounding over the edge of a boardMove left to right on the outside edgeSeveral light passes beat one deep pass#11

Router

Shapes edges, cuts grooves and makes joints.

$60 to $300

Rotary hammer (SDS)Drilling a hole in a concrete wall for an anchorHammer mode for concrete and blockEye protection and a mask for the dust#12

Rotary hammer (SDS)

Drills concrete and stone with ease, and chisels tile and mortar.

$80 to $400

Framing nailerNailing a wall frame together on the floorKeep your other hand well awayTwo 16d nails per stud#13

Framing nailer

Drives 3-1/2 inch nails in one shot: framing goes many times faster.

$120 to $550

ChainsawCutting firewood on a sawbuckChaps, helmet, face screen, ear muffs, glovesBoth hands; beware kickback at the tip#14

Chainsaw

Cuts trees, firewood and big timbers.

$200 to $600

Wet/dry shop vacuumCleaning up sawdust, water and debrisDry filter for dust, foam sleeve for waterTap the filter clean; empty it before it fills#15

Wet/dry shop vacuum

Cleans up sawdust, debris and water, and collects dust from your tools.

$70 to $600

At a glance

#ToolBest forTypical cost
1Cordless drill/driverDrills holes and drives screws. If you buy one power tool, buy this one.$60 to $250
2Impact driverDrives long screws and lag bolts that would stall a drill.$80 to $250
3Circular sawThe saw that builds houses: cuts boards and plywood fast and straight.$60 to $400
4Reciprocating sawThe demolition saw: cuts nails, pipe, limbs and walls.$60 to $260
5JigsawCuts curves, circles and cut-outs in plywood and thin boards.$40 to $230
6Miter sawPerfect square and angled cross-cuts, every time.$130 to $700
7Table sawThe most accurate saw for ripping boards and plywood to width.$300 to $2,000
8Random orbit sanderSmooths wood fast without leaving swirl marks.$40 to $450
9Angle grinderCuts and grinds steel, sharpens tools, and cuts tile and stone.$30 to $260
10Oscillating multi-toolFlush cuts, plunge cuts, scraping and detail sanding in tight spots.$60 to $400
11RouterShapes edges, cuts grooves and makes joints.$60 to $300
12Rotary hammer (SDS)Drills concrete and stone with ease, and chisels tile and mortar.$80 to $400
13Framing nailerDrives 3-1/2 inch nails in one shot: framing goes many times faster.$120 to $550
14ChainsawCuts trees, firewood and big timbers.$200 to $600
15Wet/dry shop vacuumCleans up sawdust, debris and water, and collects dust from your tools.$70 to $600

Prices are typical U.S. store prices checked November 17, 2026. They change often with sales; check the store. Tools Critical is not paid by any store or brand.