Tools Critical

The 30 most useful tools, and how to use them

by Edward J. Thunderbird

15 power tools and 15 hand tools: why you would choose each one, how to use it safely, how to keep it working, what it costs and where to buy it. Then see which tools build a house or a shed, with power or by hand.

15 power tools

Drill, saws, sander, grinder, nailer, chainsaw and more.

15 hand tools

Hammer, tape, square, level, saws, chisels and more.

Projects

Which tools for a house, a shed and everyday jobs.

Where to buy

Stores, battery brands, deals and a starter kit.

Power tools

Cordless drill/driverDrilling a pilot hole straight down into a boardLight pressure; let the bit workClutch low for screws,drill mode for holes#1

Cordless drill/driver

Drills holes and drives screws. If you buy one power tool, buy this one.

$60 to $250

Impact driverDriving a long screw into a 4x4 postHex bits only; it hammers as it turnsGreat for lag screws, deck screws, bolts#2

Impact driver

Drives long screws and lag bolts that would stall a drill.

$80 to $250

Circular sawCross-cutting a 2x10 on two sawhorsesBlade 1/4 inch below the boardSupport both sides so the cut does not pinch#3

Circular saw

The saw that builds houses: cuts boards and plywood fast and straight.

$60 to $400

Reciprocating sawCutting a tree limb, or a pipe or nails during demolitionPress the shoe against the workSwap blades: wood, metal or demolition#4

Reciprocating saw

The demolition saw: cuts nails, pipe, limbs and walls.

$60 to $260

JigsawCutting a curve in plywood clamped to a benchGood side DOWN: the blade cuts on the upstrokeSlow down on tight curves#5

Jigsaw

Cuts curves, circles and cut-outs in plywood and thin boards.

$40 to $230

Miter sawCutting trim and framing at exact anglesKeep your hand 6+ inches from the bladeLet the blade stop before lifting it#6

Miter saw

Perfect square and angled cross-cuts, every time.

$130 to $700

Table saw (seen from above)Ripping a long board with the fence and a push stickbladeFence keeps the board straightPush stick, guard and riving knife ONStand to the side of the blade, never directly behind it.#7

Table saw

The most accurate saw for ripping boards and plywood to width.

$300 to $2,000

Random orbit sanderSmoothing a tabletop, 80 to 120 to 220 gritLet its weight do it; do not press hardKeep it moving; hook up a vac#8

Random orbit sander

Smooths wood fast without leaving swirl marks.

$40 to $450

Angle grinderCutting steel angle iron with a cut-off wheelGuard on, side handle on, both handsFace shield and gloves; sparks fly far#9

Angle grinder

Cuts and grinds steel, sharpens tools, and cuts tile and stone.

$30 to $260

Oscillating multi-toolFlush-cutting a door jamb so new flooring slides underThe blade vibrates, not spinsCuts flush, plunges, scrapes and sands#10

Oscillating multi-tool

Flush cuts, plunge cuts, scraping and detail sanding in tight spots.

$60 to $400

RouterRounding over the edge of a boardMove left to right on the outside edgeSeveral light passes beat one deep pass#11

Router

Shapes edges, cuts grooves and makes joints.

$60 to $300

Rotary hammer (SDS)Drilling a hole in a concrete wall for an anchorHammer mode for concrete and blockEye protection and a mask for the dust#12

Rotary hammer (SDS)

Drills concrete and stone with ease, and chisels tile and mortar.

$80 to $400

Framing nailerNailing a wall frame together on the floorKeep your other hand well awayTwo 16d nails per stud#13

Framing nailer

Drives 3-1/2 inch nails in one shot: framing goes many times faster.

$120 to $550

ChainsawCutting firewood on a sawbuckChaps, helmet, face screen, ear muffs, glovesBoth hands; beware kickback at the tip#14

Chainsaw

Cuts trees, firewood and big timbers.

$200 to $600

Wet/dry shop vacuumCleaning up sawdust, water and debrisDry filter for dust, foam sleeve for waterTap the filter clean; empty it before it fills#15

Wet/dry shop vacuum

Cleans up sawdust, debris and water, and collects dust from your tools.

$70 to $600

Hand tools

Claw hammerDriving a 16d nail; hold near the end of the handleStart with light taps; then full swingsEye protection: nails and heads can fly#1

Claw hammer

Drives and pulls nails. Still the most-used tool in any toolbox.

$15 to $60

Tape measureMeasuring and marking a boardHook on the end moves on purpose (for inside and outside)Mark with a V: the point is the measurement#2

Tape measure

Every project starts with a measurement.

$10 to $35

Speed squareMarking a square line across a 2x4Lip on the edge = a true 90Also marks 45s and roof angles#3

Speed square

Draws square and angled lines, and lays out roof rafters.

$8 to $30

LevelChecking that a shelf is level before screwing it downBubble between the lines = levelEnd vials check plumb#4

Level

Checks level (flat) and plumb (straight up and down).

$10 to $150

Chalk lineSnapping a long straight cutting line on plywoodPull tight, lift straight up in the middle, let go: SNAPBlue chalk wipes off; red is permanent#5

Chalk line

Snaps long, perfectly straight lines in seconds.

$10 to $35

Utility knifeScoring drywall along a straightedgeCut away from your body and handChange blades often; dull ones slip#6

Utility knife

Cuts drywall, carpet, roofing, rope, boxes and plastic.

$8 to $25

Hand sawCross-cutting a 2x4 on a sawhorseMost Western saws cut on the pushStart with a few pull strokes#7

Hand saw

Cuts wood anywhere, with no power and no noise.

$15 to $60

Chisel and malletCutting a shallow notch (a hinge mortise) in a door edgeBevel side toward the wasteSharp chisels are safer than dull ones#8

Chisels and mallet

Cuts notches, cleans joints, and fits hinges and locks.

$25 to $150

Block planeShaving a sticking door edge or chamfering a boardSet it for paper-thin shavingsPlane with the grain, downhill#9

Block plane

Shaves wood: fixes sticking doors and smooths edges.

$30 to $200

ScrewdriversTightening a hinge screw by handMatch the tip to the screw head (Phillips #2 is most common)Push in hard while you turn so it does not cam out#10

Screwdrivers

Turns screws in places a drill cannot, and controls tiny ones.

$15 to $60

PliersLocking pliers gripping a rusted nut so it can be turnedLocking pliers clamp on and stay onSlip-joint, needle-nose: grip, bend wirePliers are not wrenches: they round off nuts#11

Pliers

Grip, hold, bend, cut and clamp.

$15 to $60

Wrenches and socketsTightening a bolt with a ratchet and socketPull toward you; do not pushSix-point sockets grip without rounding#12

Wrenches and sockets

Tightens and loosens nuts and bolts on everything from mowers to trucks.

$20 to $200

Pry bar (flat bar)Pulling an old nail and prying off trimSlip a scrap of wood under it to protect the surfaceA longer bar gives more leverage#13

Pry bar (flat bar)

Pulls nails, pries boards and moulding, and lifts heavy things.

$12 to $50

ClampsBar clamps holding a glued-up panel while it driesSnug, not crushing: a little glue should squeeze outAlternate clamps top and bottom to keep it flat#14

Clamps

A third and fourth hand: hold parts while you glue, cut or fasten.

$15 to $60 each

Brace and bitBoring a hole by hand, no electricity neededLean on the top knob, crank the handleBore from both sides to avoid splintering#15

Brace and bit

Bores clean holes by hand, with no power at all.

$20 to $80

Build something

10Finished

Build a house

Step by step in pictures: power tools vs. hand tools only.

6Siding, door and trim: done

Build a shed

An 8x12 shed in pictures: tools, time and cost.

Tool safety

The gear and ten habits that prevent most injuries.

Prices are typical U.S. store prices checked November 17, 2026. They change often with sales; check the store. Tools Critical is not paid by any store or brand.